- NZNOG - lists.nznog.org

FW: [nsp] Cisco Security Advisory: Cisco IOS Software SNMP Read-Write ILMI Community String Vulnerability
by Barry Raveendran Greene 27 Feb '01

27 Feb '01

-----Original Message----- From: nobody(a)cisco.com [mailto:nobody(a)cisco.com]On Behalf Of Cisco Systems Product Security Incident Response Team Sent: Tuesday, February 27, 2001 1:00 AM To: cisco-nsp(a)puck.nether.net Cc: psirt(a)cisco.com Subject: [nsp] Cisco Security Advisory: Cisco IOS Software SNMP Read-Write ILMI Community String Vulnerability -----BEGIN PGP SIGNED MESSAGE----- Cisco Security Advisory: Cisco IOS Software SNMP Read-Write ILMI Community String Vulnerability Revision 1.0: INTERIM For Public Release 2001 February 27 04:00 US/Eastern (UTC+0500) _______________________________________________________________ Summary Cisco IOS software releases based on versions 11.x and 12.0 contain a defect that allows a limited number of SNMP objects to be viewed and modified without authorization using a undocumented ILMI community string. Some of the modifiable objects are confined to the MIB-II system group, such as "sysContact", "sysLocation", and "sysName", that do not affect the device's normal operation but that may cause confusion if modified unexpectedly. The remaining objects are contained in the LAN-EMULATION-CLIENT and PNNI MIBs, and modification of those objects may affect ATM configuration. An affected device might be vulnerable to a denial-of-service attack if it is not protected against unauthorized use of the ILMI community string. The vulnerability is only present in certain combinations of IOS releases on Cisco routers and switches. ILMI is a necessary component for ATM, and the vulnerability is present in every IOS release that contains the supporting software for ATM and ILMI without regard to the actual presence of an ATM interface or the physical ability of the device to support an ATM connection. To remove this vulnerability, Cisco is offering free software upgrades for all affected platforms. The defect is documented in DDTS record CSCdp11863. In lieu of a software upgrade, a workaround can be applied to certain IOS releases by disabling the ILMI community or "*ilmi" view and applying an access list to prevent unauthorized access to SNMP. Any affected system, regardless of software release, may be protected by filtering SNMP traffic at a network perimeter or on individual devices. This notice will be posted at http://www.cisco.com/warp/public/707/ios-snmp-ilmi-vuln-pub.shtml. Affected Products The vulnerability is present only in certain releases of Cisco IOS Software versions 11.x and 12.0 for router and switch products that include support for Asynchronous Transfer Mode (ATM) networking and Interim Local Management Interface (ILMI), and it is present without regard to any physical capability for supporting an ATM interface. Cisco IOS Software versions based on 10.3 and earlier do not contain the vulnerability. The defect was introduced in 11.0(0.2). All Cisco IOS software releases of 12.1 and later have been repaired and are not vulnerable to the defect described in this advisory. To determine the software running on a Cisco product, log in to the device and issue the command "show version" to display the system banner. Cisco IOS software will identify itself as "Internetwork Operating System Software" or simply "IOS (tm)". The image name will be displayed between parentheses, usually on the next line of output, followed by "Version" and the IOS release name. Other Cisco devices will not have the "show version" command or will give different output. The following example identifies a Cisco product running IOS release 12.0(3) with an installed image name of C2500-IS-L: Cisco Internetwork Operating System Software IOS (tm) 2500 Software (C2500-IS-L), Version 12.0(3), RELEASE SOFTWARE The device is not vulnerable to the defect described in this advisory since the model 2500 router is specifically excluded in the list of unaffected products shown below. Cisco devices that may be running an affected IOS software release include, but are not limited to: * Cisco 1400 and 1700 series. * Cisco 2600 (except that c2600-c-mz, c2600-d-mz, c2600-i-mz, c2600-io3-mz, and c2600-ix-mz images are not vulnerable). * Catalyst 2900 ATM, 2900XL, and 2948g series. * Cisco 3620 (except that c3620-d-mz, c3620-i-mz, c3620-io3-mz, and c3620-ix-mz images are not vulnerable). * Cisco 3640 (except that c3640-d-mz, c3640-i-mz, c3640-io3-mz, and c3640-ix-mz images are not vulnerable). * Cisco 3660 (except that c3660-d-mz, c3660-i-mz, and c3660-ix-mz images are not vulnerable). * Cisco MC3810 (except that mc3810-i-mz, mc3810-is-mz, mc3810-is56i-mz, and mc3810-js-mz images are not vulnerable). * Catalyst 4232, 4840g, 5000 RSFC series switches. * Cisco 4500, 4700, and 5800 DSC series. * Cisco 6200, 6400 NRP, and 6400 NSP series. * Catalyst MSM (c6msm), 6000 Hybrid Mode (c6msfc), and 6000 Native Mode (c6sup). * Cisco RSM, 7000, 7010, 7100, 7200, ubr7200, and 7500 series. * Catalyst 8510CSR, 8510MSR, 8540CSR, and 8540MSR series. * Cisco 10000 ESR and 12000 GSR series. * LS1010 and Cisco 6260-NI2. * DistributedDirector (except that igs-w3 images are not vulnerable). Cisco products that are not affected by this vulnerability either because they have no support for ATM and ILMI, or because they do not run IOS include, but are not limited to: * Catalyst ATM blade (runs possibly affected code, but an SNMP connection to the blade is not possible). * Cisco 800 and 805 series. * Cisco Universal Broadband Routers ubr900 and ubr920. * Cisco 1003, 1004, and 1005 series. * Cisco 1600, 2500, 2800, 4000 series. * Cisco 2500 Fixed Frad. * Cisco 3800 (not to be confused with MC3810). * Cisco 5100, 5200, and 5300 series access servers. * Catalyst 6000 Supervisor Module. * Cisco PIX Firewall. * Aironet and Cisco/Aironet wireless products. * CS11000, Cache Engine, LocalDirector, and network scaling products (except that the Distributed Director might be affected). * VPN products such as Altiga concentrators. * Host-based network management or access management products. * Cisco IP Telephony and telephony management software (except those that are hosted on a vulnerable IOS platform). * Voice gateways and convergence platforms (except those that are hosted on a vulnerable IOS platform). * Optical switch products such as the ONS 15000 series. Details ILMI (Interim Local Management Interface) is an independent industry standard used for configuration of ATM (Asynchronous Transfer Mode) interfaces. The standard specifies the use of mechanisms and formats previously defined by SNMP (Simple Network Management Protocol). Although it is based on SNMP, ILMI communication actually occurs using a transport other than IP (Internet Protocol) that traverses only the physical ATM link. ILMI is essential to functions such as ATM auto-discovery and LANE (LAN Emulation). SNMP "objects" are variables that are organized into a MIB (Management Information Base). The MIB has a tree structure and contains both operational (read-only) data as well as configuration (read-write) options. By specifying a community string of "ILMI" in an SNMP request, access can be obtained to read the objects in three specific parts of the overall management tree structure on any device affected by this vulnerability: the MIB-II system group, the LAN-EMULATION-CLIENT MIB, and the PNNI (Private Network-to-Network Interface) MIB. A subset of objects in each part can be modified using the same "ILMI" community string. The MIB-II system group contains basic information about the device itself. The number of objects that can be modified is limited. Examples include: * system.sysContact: The contact information for the person or organization responsible for managing the device. * system.sysLocation: A description of the physical location where the device is installed or operating. * system.sysName: The hostname of the device, how it identifies itself at the console prompt. (This might not be the same name by which the device is known to other hosts on the network.) Most of the objects in the system MIB are read-only and cannot be changed via SNMP, such as the time elapsed since the previous restart and textual descriptions of the device's hardware and software. Numerous objects can be viewed in the LAN-EMULATION-CLIENT MIB and PNNI MIB, and modification of some of the read-write objects can have an affect on ATM operation of the device. The objects in the LAN-EMULATION-CLIENT MIB can only be viewed or modified if LANE has already been configured on the device. Access to SNMP in Cisco IOS software can be limited by applying access control lists (ACLs), by modifying or removing the SNMP view, by removing the community string from the running configuration, or by disabling the SNMP service. Any SNMP query that does not meet the criteria for access is promptly discarded when such protective measures are in place. If a query does meet the criteria for access, then a response is formulated and sent. It is possible to configure the device so that the ILMI community string is unavailable in all IOS 11.1 and higher releases. The particular method selected to accomplish this depends on the specific IOS release and configuration. This defect is documented as CSCdp11863. The vulnerability is repaired by imposing a test such that an SNMP request using the "ILMI" community string will only be recognized if it has been transported by ILMI. ATM functionality was added in various 10.x releases of Cisco IOS software. However, the function containing the defect was introduced when support for ILMI and other ATM features was added in IOS release 11.0(0.2). Therefore, all prior releases are not vulnerable. Impact If SNMP requests can be received by an affected device, then certain MIB objects can be viewed without proper authorization, causing a violation of confidentiality. A subset of the readable MIB objects can be modified without authorization to cause a failure of integrity. For example, the hostname can be modified so as to confuse network adminstrators, or the contact and location information could be changed with a goal of disrupting operations or embarassing whoever is responsible for the device. Objects in the LAN-EMULATION-CLIENT and PNNI MIBs can be viewed and modified, thus resulting in changes to the operation of ATM functions. If ATM is in use on the device, this may result in a failure of availability. Any affected device that is not otherwise protected against the receipt of SNMP packets is vulnerable to a denial-of-service (DoS) attack by flooding the SNMP port with read or write requests. Software Versions and Fixes The following table summarizes the known affected Cisco IOS software releases and the earliest estimated dates of availability for fixed releases. All dates are tentative and subject to change. Each row of the table describes a release train and the platforms or products for which it is intended. If a given release train is vulnerable, then the earliest possible releases that contain the fix and the anticipated date of availability for each are listed in the "Rebuild", "Interim", and "Maintenance" columns. If a device is running an earlier release that is known to be vulnerable, it should be upgraded to at least the indicated version. When selecting a release, keep in mind the following definitions: Maintenance Most heavily tested and highly recommended release of any label in a given row of the table. Rebuild Constructed from the previous maintenance or major release in the same train, it contains the fix for a specific defect. Although it receives less testing, it contains only the minimal changes necessary to effect the repair. Interim Built at regular intervals between maintenance releases and receive less testing. Interims should be selected only if there is no other suitable release that addresses the vulnerability. Interim releases are usually not available for customer download via CCO without prior arrangement. In all cases, customers should exercise caution to be certain the devices to be upgraded contain sufficient memory and that current hardware and software configurations will continue to be supported properly by the new release. If the information is not clear, contact the Cisco TAC for assistance as shown in the following section. More information on IOS release names and abbreviations is available at http://www.cisco.com/warp/public/620/1.html. +=========================================================================== + | Train | Description of | Availability of Fixed Releases* | | | Image or Platform | | +=========================================================================== + | 10.3-based Releases and | | | | | Earlier | Rebuild | Interim** | Maintenance | +=========================================================================== + | 10.3 and | | | | earlier |All |Not affected | +=========================================================================== + | 11.0-based Releases | Rebuild | Interim** | Maintenance | +=========================================================================== + | | |11.0(22a) | | | | 11.0 |Major GD release | | | | | |for all platforms |2001-Mar-05 | | | +=========================================================================== + | 11.1-based Releases | Rebuild | Interim** | Maintenance | +=========================================================================== + | | |11.1(24a) | | | | 11.1 |Major release for | | | | | |all platforms |2001-Mar-05 | | | +----------+-------------------+------------+---------------+--------------- + | |ED release for | | |12.1(7) | | 11.1AA |access servers: | | | | | |1600, 3200, and | | | | | |5200 series. | | |2001-Feb-26 | +----------+-------------------+------------+---------------+--------------- + | |Platform-specific |11.1(36)CA1 | | | | 11.1CA |support for 7500, | | | | | |7200, 7000, and RSP|2001-Mar-02 | | | +----------+-------------------+------------+---------------+--------------- + | |ISP train: added | | | | | |support for FIB, |11.1(36)CC1 | | | | 11.1CC |CEF, and NetFlow on| | | | | |7500, 7200, 7000, |2001-Mar-02 | | | | |and RSP | | | | +----------+-------------------+------------+---------------+--------------- + | |Added support for |12.0(11)ST2 | | | | 11.1CT |Tag Switching on | | | | | |7500, 7200, 7000, | | | | | |and RSP |2001-Feb-26 | | | +----------+-------------------+------------+---------------+--------------- + | | |11.1(28)IA1 | | | | 11.1IA |DistributedDirector| | | | | |only |2001-Feb-26 | | | +=========================================================================== + | 11.2-based Releases | Rebuild | Interim** | Maintenance | +=========================================================================== + | | |11.2(25a) | | | | 11.2 |Major release, | | | | | |general deployment |2001-Mar-05 | | | +----------+-------------------+------------+---------------+--------------- + | |Platform-specific | | | | | |support for IBM | | |12.1(7) | | 11.2BC |networking, CIP, | | | | | |and TN3270 on 7500,| | |2001-Feb-26 | | |7000, and RSP | | | | +----------+-------------------+------------+---------------+--------------- + | |Early deployment |12.0(15)S1 | | | | 11.2GS |release to support | | | | | |12000 GSR |2001-Feb-20 | | | +----------+-------------------+------------+---------------+--------------- + | | |11.2(25a)P | | | | 11.2P |New platform | | | | | |support |2001-Mar-05 | | | +----------+-------------------+------------+---------------+--------------- + | | | | |12.1WC | | 11.2SA |Catalyst 2900XL | | | | | |switch only | | |2001-Apr-12 | +----------+-------------------+------------+---------------+--------------- + | | | | |12.0(10)W5(18c)| | 11.2WA3 |LS1010 ATM switch | | | | | | | | |Available | +----------+-------------------+------------+---------------+--------------- + | | |11.2(25a)P | | | |11.2(4)XA |Initial release for| | | | | |the 1600 and 3600 |2001-Mar-05 | | | +----------+-------------------+------------+---------------+--------------- + | |Initial release for| | | | | |the 5300 and |11.2(9)XA1 | | | |11.2(9)XA |digital modem | | | | | |support for the |Unscheduled | | | | |3600 | | | | +=========================================================================== + | 11.3-based Releases | Rebuild | Interim** | Maintenance | +=========================================================================== + | | |11.3(11b) | | | | 11.3 |Major release for | | | | | |all platforms |2001-Mar-05 | | | +----------+-------------------+------------+---------------+--------------- + | |ED for dial | | | | | |platforms and |11.3(11a)AA | | | | 11.3AA |access servers: | | | | | |5800, 5200, 5300, |2001-Mar-05 | | | | |7200 | | | | +----------+-------------------+------------+---------------+--------------- + | |Early deployment |12.1(5)DA1 | | | | 11.3DA |train for ISP DSLAM| | | | | |6200 platform |2001-Feb-28 | | | +----------+-------------------+------------+---------------+--------------- + | |Early deployment | | | | | |train for |12.1(4)DB1 | | | | |ISP/Telco/PTT xDSL | | | | | 11.3DB |broadband | | | | | |concentrator | | | | | |platform, (NRP) for|2001-Feb-26 | | | | |6400 | | | | +----------+-------------------+------------+---------------+--------------- + | |Short-lived ED | | | 11.3HA |release for ISR |Not Vulnerable | | |3300 (SONET/SDH | | | |router) | | +----------+-------------------+------------+---------------+--------------- + | | |11.3(1)MA8 | | | | 11.3MA |MC3810 | | | | | |functionality only |Unscheduled | | | +----------+-------------------+------------+---------------+--------------- + | |Voice over IP, |12.1(7) | | | | 11.3NA |media convergence, | | | | | |various platforms |2001-Mar-05 | | | +----------+-------------------+------------+---------------+--------------- + | |Early deployment |11.3(11b)T1 | | | | 11.3T |major release, | | | | | |feature-rich for | | | | | |early adopters |2001-Mar-05 | | | +----------+-------------------+------------+---------------+--------------- + | |Multilayer | | | | | |Switching and | | |12.0(14)W5(20) | | |Multiprotocol over | | | | | 11.3WA4 |ATM functionality | | | | | |for Catalyst 5000 | | | | | |RSM, 4500, 4700, | | |2001-Feb-28 | | |7200, 7500, LS1010 | | | | +----------+-------------------+------------+---------------+--------------- + | | |11.3(11b)T1 | | | |11.3(2)XA |Introduction of | | | | | |ubr7246 and 2600 |2001-Mar-05 | | | +=========================================================================== + | 12.0-based Releases | Rebuild | Interim** | Maintenance | +=========================================================================== + | |General deployment | |12.0(7.1) |12.0(16) | | 12.0 |release for all | | | | | |platforms | |Available |2001-Feb-20 | +----------+-------------------+------------+---------------+--------------- + | | | |12.0(7.1)T | | | 12.0DA |xDSL support: 6100,| | | | | |6200 | |Available | | +----------+-------------------+------------+---------------+--------------- + | |ISP/Telco/PTT xDSL |12.1(4)DB1 | | | | 12.0DB |broadband | | | | | |concentrator | | | | | |platforms |2001-Feb-26 | | | +----------+-------------------+------------+---------------+--------------- + | | |12.1(4)DC2 | | | | 12.0DC |6400 Access | | | | | |Concentrator |2001-Feb-26 | | | +----------+-------------------+------------+---------------+--------------- + | | |12.0(15)S1 | | | | 12.0S |Core/ISP support: | | | | | |GSR, RSP, c7200 |2001-Feb-20 | | | +----------+-------------------+------------+---------------+--------------- + | | |12.0(15)SC1 | | | | 12.0SC |Cable/broadband | | | | | |ISP: ubr7200 |2001-Feb-26 | | | +----------+-------------------+------------+---------------+--------------- + | | |12.0(14)SL1 | | | | 12.0SL |10000 ESR: c10k | | | | | | |2001-Feb-26 | | | +----------+-------------------+------------+---------------+--------------- + | |General deployment |12.0(11)ST2 | | | | 12.0ST |release for all | | | | | |platforms |2001-Feb-26 | | | +----------+-------------------+------------+---------------+--------------- + | | |12.1(5c)E8 | | | | 12.0SX |Early Deployment | | | | | |(ED) |2001-Feb-26 | | | +----------+-------------------+------------+---------------+--------------- + | |Early | | | | | |Deployment(ED): | | |12.1(7) | | 12.0T |VPN, Distributed | | | | | |Director, various | | |2001-Feb-26 | | |platforms | | | | +----------+-------------------+------------+---------------+--------------- + | |cat8510c, cat8540c,| | | | | |ls1010, cat8510m, | |12.0(10)W5(18c)|12.0(14)W5(20) | | |cat8540m, c5atm, | | | | | |c5atm, c3620, | | | | | |c3640, c4500, | | | | | 12.0W5 |c5rsfc, c5rsm, | |Available |2001-Feb-28 | | |c7200, rsp, | | | | | |cat2948g, cat4232 | | | | | +-------------------+------------+---------------+---------------+ | | | |12.0(10)W5(18d)|12.0(14)W5(20) | | |c6msm | | | | | | | |Available |2001-Feb-28 | +----------+-------------------+------------+---------------+--------------- + | |General deployment | | |12.0(13)WT6(1) | | 12.0WT |release for all | | | | | |platforms | | |2001-Feb-20 | +----------+-------------------+------------+---------------+--------------- + | |Early Deployment | | |12.1(7) | | 12.0XA |(ED): limited | | | | | |platforms | | |2001-Feb-26 | +----------+-------------------+------------+---------------+--------------- + | | | | |12.1(7) | | 12.0XB |Short-lived early | | | | | |deployment release | | |2001-Feb-26 | +----------+-------------------+------------+---------------+--------------- + | |Early Deployment | | |12.1(7) | | 12.0XC |(ED): limited | | | | | |platforms | | |2001-Feb-26 | +----------+-------------------+------------+---------------+--------------- + | |Early Deployment | | |12.1(7) | | 12.0XD |(ED): limited | | | | | |platforms | | |2001-Feb-26 | +----------+-------------------+------------+---------------+--------------- + | |Early Deployment |12.1(5c)E8 | | | | 12.0XE |(ED): limited | | | | | |platforms |2001-Feb-26 | | | +----------+-------------------+------------+---------------+--------------- + | |Early Deployment | | |12.1(7) | | 12.0XF |(ED): limited | | | | | |platforms | | |2001-Feb-26 | +----------+-------------------+------------+---------------+--------------- + | |Early Deployment | | |12.1(7) | | 12.0XG |(ED): limited | | | | | |platforms | | |2001-Feb-26 | +----------+-------------------+------------+---------------+--------------- + | |Early Deployment |12.0(4)XH5 | | | | 12.0XH |(ED): limited | | | | | |platforms |2001-Mar-05 | | | +----------+-------------------+------------+---------------+--------------- + | |Early Deployment | | |12.1(7) | | 12.0XI |(ED): limited | | | | | |platforms | | |2001-Feb-26 | +----------+-------------------+------------+---------------+--------------- + | |Early Deployment | | |12.1(7) | | 12.0XJ |(ED): limited | | | | | |platforms | | |2001-Feb-26 | +----------+-------------------+------------+---------------+--------------- + | |Early Deployment |12.0(7)XK4 | | | | 12.0XK |(ED): limited | | | | | |platforms |Unscheduled | | | +----------+-------------------+------------+---------------+--------------- + | |Early Deployment |12.0(4)XH5 | | | | 12.0XL |(ED): limited | | | | | |platforms |2001-Mar-05 | | | +----------+-------------------+------------+---------------+--------------- + | | | | |12.1(7) | | 12.0XM |Short-lived early | | | | | |deployment release | | |2001-Feb-26 | +----------+-------------------+------------+---------------+--------------- + | |Early Deployment | | | | | 12.0XN |(ED): limited | | | | | |platforms | | | | +----------+-------------------+------------+---------------+--------------- + | |Early Deployment | | |12.1WC | | 12.0XP |(ED): limited | | | | | |platforms | | |2001-Apr-12 | +----------+-------------------+------------+---------------+--------------- + | | | | |12.1(7) | | 12.0XQ |Short-lived early | | | | | |deployment release | | |2001-Feb-26 | +----------+-------------------+------------+---------------+--------------- + | | |12.1(5)T5 | | | | 12.0XR |Short-lived early | | | | | |deployment release |2001-Mar-05 | | | +----------+-------------------+------------+---------------+--------------- + | | |12.1(5c)E8 | | | | 12.0XS |Short-lived early | | | | | |deployment release |2001-Feb-26 | | | +----------+-------------------+------------+---------------+--------------- + | |Early Deployment | | |12.1WC | | 12.0XU |(ED): limited | | | | | |platforms | | |2001-Apr-12 | +----------+-------------------+------------+---------------+--------------- + | | |12.1(5)T5 | | | | 12.0XV |Short-lived early | | | | | |deployment release |2001-Mar-05 | | | +=========================================================================== + |12.1-based and Later Releases | Rebuild | Interim** | Maintenance | +=========================================================================== + | All 12.1 | | | | Releases |Various platforms |Not Vulnerable | +=========================================================================== + | Notes | +=========================================================================== + | * All dates are estimated and Subject to change. | | | |** Interim releases are subjected to less rigorous testing than regular | | maintenance releases, and may have serious bugs. | +=========================================================================== + Obtaining Fixed Software Cisco is offering free software upgrades to remedy this vulnerability for all affected customers. Customers with service contracts may upgrade to any software release. Customers without contracts may upgrade only within a single row of the table above, except that any available fixed software release will be provided to any customer who can use it and for whom the standard fixed software release is not yet available. Customers may install only the feature sets they have purchased. Note that not all fixed software may be available as of the release date of this notice. Customers with contracts should obtain upgraded software through their regular update channels. For most customers, this means that upgrades should be obtained via Cisco's Software Center at http://www.cisco.com/. Customers without contracts or warranty should get their upgrades by contacting the Cisco Technical Assistance Center (TAC) as shown below: * (800) 553-2447 (toll-free in North America) * +1 408 526 7209 (toll call from anywhere in the world) * e-mail: tac(a)cisco.com See http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml for additional TAC contact information, including instructions and e-mail addresses for use in various languages. Give the URL of this notice as evidence of your entitlement to a free upgrade. Free upgrades for non-contract customers must be requested through the TAC. Please do not contact either "psirt(a)cisco.com" or "security-alert(a)cisco.com" for software upgrades; faster results will be obtained by contacting the TAC directly. Workarounds Several workarounds are available based on customer needs, equipment, and software features. The usefulness and practicality of each workaround depends on the IOS release running on the device and many variables in the customer's environment. Customers are urged to consider each of the following alternatives carefully before deploying. These workarounds are only needed if it is not possible to upgrade to an unaffected release of IOS software. A. Default workaround for use with releases for which no other workarounds are effective: 1. Applying access lists to all the interfaces of the vulnerable device blocking SNMP from all hosts but those authorized to manage the devices. 2. Blocking SNMP access at the edge of the network to prevent undesirable SNMP traffic from entering the network containing the vulnerable device. Access lists should be deployed with careful consideration of the possible effects on network operation and performance. Also note that authentication based on an IP source address is weak, so the preceding method will not protect against certain types of attacks in which the IP source address has been spoofed. Further information can be found in the Cisco document "Improving Security on Cisco Routers", available at http://www.cisco.com/warp/public/707/21.html B. For affected releases based on IOS 11.1: 1. Remove the view so that the ILMI community cannot be reached: no snmp-server view *ilmi 2. This configuration will not survive a system reload. The command must be re-entered after every restart of the system. C. For affected releases of IOS 11.2 through 11.3(8) NOT REQUIRING ATM: In this affected range of releases, the ILMI community string can be modified or deleted. However, the changes will not persist through a reboot of the device. These instructions must be re-applied following every system reload of the affected device: 1. Expose the undocumented ILMI community string so it can be modified: snmp-server community ILMI RW The preceding command may cause an error that can be safely ignored. 2. Disable read-write capability for the same community: no snmp-server community ILMI RW If an error is displayed, then this workaround cannot be applied to the device. Use the default workarounds presented in the first item above. 3. Since this configuration will not survive a system reload, the command must be re-entered after every restart of the system. If the command in item 2 above did not generate an error and ATM is not needed on this device, then this workaround is complete. D. For affected releases of IOS 11.2 through 11.3(8) THAT REQUIRE ATM: This workaround will allow ILMI to continue to function for ATM while constraining who may reconfigure the device by way of the ILMI community string: 1. Create a simple ACL to deny access using the following command. If "66" is already in use, choose a different two-digit number: access-list 66 deny any 2. Apply it generally to the ILMI community to restrict its view: snmp community ILMI view *ilmi RW 66 An error will be reported if the *ilmi view doesn't exist. If that occurs, then use the following command to explicitly restrict the ILMI view: snmp community ILMI RW 66 If the preceding command produces persistent errors, then this workaround cannot be applied to this device. Use the default workarounds presented in the first item above. E. For affected releases of IOS 11.3(9) through 12.0(2)T NOT REQUIRING ATM: All versions of IOS in this range will accept this workaround, and the change will remain in place after a system reload. 1. Expose the undocumented ILMI community string so it can be modified: snmp-server community ILMI RW The preceding command may cause an error that can be safely ignored. 2. Disable read-write capability for the same community: no snmp-server community ILMI RW If an error is displayed, then this workaround cannot be applied to the device. Stop this procedure and use the default workarounds presented in the first item above. F. For affected releases of IOS 11.3(9) through 12.0(2)T THAT REQUIRE ATM: This workaround will allow ILMI to continue to function for ATM while constraining who may reconfigure the device by way of the ILMI community string: 1. Create a simple ACL to deny access using the following command. If "66" is already in use, choose a different two-digit number: access-list 66 deny any 2. Apply it generally to the ILMI community to restrict its view: snmp community ILMI view *ilmi RW 66 An error will be reported if the *ilmi view doesn't exist. If that occurs, then use the following command to explicitly restrict the ILMI view: snmp community ILMI RW 66 If the preceding command produces persistent errors, then this workaround cannot be applied to this device. Use the default workaround presented in the first item above. G. For affected releases of IOS 12.0(3)T and later: These releases of IOS include support for Simple Network Management Protocol version 3 (SNMPv3), which is required for this workaround. 1. Confirm the presence of SNMPv3 support by asking the console CLI (command-line interpreter) for assistance with options to complete the snmp-server command. Enter config mode, enter the command shown below, and note the expected response: snmp-server user test test ? remote Specify a remote SNMP entity to which the user belongs v1 user using the v1 security model v2c user using the v2c security model v3 user using the v3 security model If the preceding command did not produce the expected results, then SNMPv3 is not supported in the release and this workaround cannot be applied. Stop this procedure and consider applying the default workaround presented above in the first item. Otherwise, if the device responded as expected, continue with the following explanation and instructions. In these IOS releases (12.0(3)T and later), ILMI packets are processed by the SNMP engine in the same manner as ordinary IP SNMP packets. An access control list or a view applied to the ILMI community string will be processed whether the transport is ILMI or IP. However, the only types of access control lists that can be applied to a community string are via IP access-list statements, which when applied, block ALL non-IP packets, including ILMI packets. Modifying or deleting the *ilmi view will also affect the packets transported by ILMI, so workarounds that change the view are equally ineffective at permitting ILMI while denying SNMP. In this range of releases, it is not possible to apply a workaround that denies IP SNMP packets that does not also deny ILMI SNMP packets. H. For affected releases of IOS 12.0(3)T and later NOT REQUIRING ATM: 1. Expose the undocumented ILMI community string so it can be modified: snmp-server community ILMI RW The preceding command may cause an error that can be safely ignored. 2. Disable read-write capability for the same community: no snmp-server community ILMI RW If an error is displayed, then this workaround cannot be applied to the device. Stop this procedure and consider using the default workaround. I. For affected releases of IOS 12.0(3)T and later THAT REQUIRE ATM: NOTE: This section also applies to 12.0-based ATM switch software such as for the LS1010 and the 8500 series. The only effective workaround for systems in this category is the default workaround: 1. Applying access lists to all the interfaces of the vulnerable device blocking SNMP from all hosts but those authorized to manage the devices. 2. Blocking SNMP access at the edge of the network to prevent undesirable SNMP traffic from entering the network containing the vulnerable device. Access lists should be deployed with careful consideration of the possible effects on network operation and performance. Also note that authentication based on an IP source address is weak, so the preceding method will not protect against certain types of attacks in which the IP source address has been spoofed. In this range of releases it is not possible to block IP SNMP packets while permitting ILMI SNMP packets. The alternative workarounds presented previously will almost certainly cause a failure of ATM ILMI communications resulting in a loss of ATM connectivity, either immediately upon configuration, or unexpectedly at some later time. Either use the default workaround or upgrade to fixed software. Exploitation and Public Announcements This vulnerability is known to the engineering staff of several Cisco customers. Cisco considers it known to the public prior to the publication of this notice. Cisco is aware of one recent incident involving the unauthorized modification of a router that appears to have resulted from this vulnerability. However, it may have been the unintended side-effect of a test of the vulnerability. Cisco is not aware of any available tools specifically designed to make use of this vulnerability. However, various off-the-shelf network management programs could easily be used to test for this vulnerability and to exploit it. Certain widely-available programs known to the cracker community could be modified by any reasonably competent programmer to automate the abuse of this vulnerability. Cisco is not aware of any general public discussion of this vulnerability other than the exceptions previously noted. Status of This Notice: INTERIM This is an interim security advisory. Cisco anticipates issuing updated versions of this notice at irregular intervals as there are material changes in the facts, and will continue to update this notice as necessary. The reader is warned that this notice may contain inaccurate or incomplete information. Although Cisco cannot guarantee the accuracy of all statements in this notice, all of the facts have been checked to the best of our ability. Cisco anticipates issuing monthly updates of this notice until it reaches FINAL status. A standalone copy or paraphrase of the text of this security advisory that omits the distribution URL in the following section is an uncontrolled copy, and may lack important information or contain factual errors. Distribution This notice will be posted at http://www.cisco.com/warp/public/707/ios-snmp-ilmi-vuln-pub.shtml . In addition to Worldwide Web posting, a text version of this notice will be clear-signed with the Cisco PSIRT PGP key and will be posted to the following e-mail and Usenet news recipients: * cust-security-announce(a)cisco.com * bugtraq(a)securityfocus.com * firewalls(a)lists.gnac.com * first-teams(a)first.org (including CERT/CC) * cisco(a)spot.colorado.edu * cisco-nsp(a)puck.nether.net * comp.dcom.sys.cisco * Various internal Cisco mailing lists Future updates of this notice, if any, will be placed on Cisco's Worldwide Web server, but may or may not be actively announced on mailing lists or newsgroups. Users concerned about this problem are encouraged to check the URL given above for any updates. Revision History Revision 1.0 2001-Feb-27 First interim public version Cisco Product Security Incident Procedures Instructions for reporting product security vulnerabilities in Cisco products, obtaining assistance with customer security incidents, and registering to receive security information from Cisco can be found at http://www.cisco.com/warp/public/707/sec_incident_response.shtml , including instructions for press inquiries regarding Cisco Security Advisories. _______________________________________________________________ Copyright 2001 by Cisco Systems, Inc. This notice may be redistributed freely after the release date given at the top of the text, provided that redistributed copies are complete and unmodified, and include all date and version information. _______________________________________________________________ -----BEGIN PGP SIGNATURE----- Version: PGP 6.5.2 iQEVAwUBOpuPFWiN3BRdFxkbAQEmvAf+Ng5nJtzMpp2Dl/N+ZDp4/4Ul1nqMt89P IcNr/9AKa/jCMKNE8z20/tql78f0oniJ3YfR2GcoFfgfRCRKEVJ5QvzH3r+8BLA2 9YRsmxg/96aVwMP9gLoh4RiO4+qoTwSZkOBJ/DlZFzM7TG8SjKvgtjqcHWiLH9wx /YnxrVWg0jmnY9NvsRQSmS4KvKjFXZXaUBzlH8pOcrY9+vScS6ol+HwCiQOynQYn 2sG+KEapKP/ld2iDcHZPjbFfVsKm+iCtMzcroqpA+ND3ezBeNe2yjJXZG9oWUiVR zLYima8yuU5Mm18b3BoBkM2npf5QP/zRinis9A8d+mlnPemAWVoWug== =xM8n -----END PGP SIGNATURE----- --------- To unsubscribe from nznog, send email to majordomo(a)list.waikato.ac.nz where the body of your message reads: unsubscribe nznog

1 0

Re: [jamesr@rd.bbc.co.uk: Warning: Cisco RW community backdoor.]
by Andy Linton 26 Feb '01

26 Feb '01

At 14:44 27/02/2001 +1300, David Robb wrote: >On Tue, 27 Feb 2001, Chris Wedgwood wrote: > > > Unless you have IOS 11.1 where this doesn't work :) > > > > "no snmp-server" > >11.2 seems to require the same treatment. I tried the "patch" on IOS 11.2 and 11.3 boxes such as 2500s and 2924 switches. I had to leave out the "log'" option on the access list. --------- To unsubscribe from nznog, send email to majordomo(a)list.waikato.ac.nz where the body of your message reads: unsubscribe nznog

1 0

Cisco IOS ILMI/SNMP
by Roger De Salis 26 Feb '01

26 Feb '01

Gentlefolks, Cisco has become aware of an issue with ILMI (and there is is another advisory pending) across several versions of IOS. Please look at the PSAT pages on www.cisco.com, as info will be available very shortly with full details. Rgds Roger De Salis James A.T. Rice wrote > Its looks like parts of my earlier email are somewhat misleading, > the ILMI community appears to only allow RW access to the system > object and possibly some more objects. Its not a 'standard' open > RW community. hence the damage caused by this backdoor is limited. > There is still some write access however, so the fix mentioned > below is still highly recommended. > > And of course - it allows people to read what IOS/model cisco > you have, which could be used to find exploitable bugs in that > particular release. Oh I wonder what the chances of having a > router stolen due to discovery of system.sysLocation is! :-) > > Warm Regards > James -- \_ Roger De Salis Cisco Systems NZ Ltd </' +64 25 481 452 L8, ASB Tower, 2 Hunter St /) +64 4 496 9003 Wellington, New Zealand (/ roger(a)desalis.gen.nz rdesalis(a)cisco.com ` --------- To unsubscribe from nznog, send email to majordomo(a)list.waikato.ac.nz where the body of your message reads: unsubscribe nznog

1 0

[jamesr@rd.bbc.co.uk: Warning: Cisco RW community backdoor.]
by Joe Abley 26 Feb '01

26 Feb '01

----- Forwarded message from "James A. T. Rice" <jamesr(a)rd.bbc.co.uk> ----- Date: Tue, 27 Feb 2001 00:39:38 +0000 (GMT) From: "James A. T. Rice" <jamesr(a)rd.bbc.co.uk> X-Sender: <jamesr(a)inet15> To: <members(a)lonap.net>, <ops(a)linx.net> Subject: Warning: Cisco RW community backdoor. Precedence: bulk If your router responds to `snmpwalk router.isp.net.uk ILMI`, you probabally will want to do the following to disable it: conf t snmp-server community ILMI RO 99 access-list 99 deny any log (pick another spare access-list if 99 isn't available) If you dont, assuming your ios/hardware combination supports it, (most of the bigger routers do) anyone can do things like: `snmpset router.isp.net.uk ILMI system.sysName.0 s \ "ALL YOUR ROUTER ARE BELONG TO US."` Thats a harmless example. You can do almost anything with RW snmp. Warm Regards James -- James A. T. Rice | Email: jamesr(a)rd.bbc.co.uk Internet Operations Engineer | Phone: 01737 839 737 BBC Internet Services, Kingswood Warren, Tadworth, Surrey, UK. ----- End forwarded message ----- --------- To unsubscribe from nznog, send email to majordomo(a)list.waikato.ac.nz where the body of your message reads: unsubscribe nznog

4 3

IOS & BGP
by James Tyson 26 Feb '01

26 Feb '01

Does anyone know what version of IOS the "bgp go faster you bitch" command appears in? It doesnt appear to be in 12.0(14)S. Sigh. Cheers. James Tyson --- Samizdat New Media Solutions --------- To unsubscribe from nznog, send email to majordomo(a)list.waikato.ac.nz where the body of your message reads: unsubscribe nznog

3 2

RE: ATM card in Cisco 4500
by Scott, Arron 26 Feb '01

26 Feb '01

Not speaking on behalf of any company in particular, I just wanted to say I know of a number of 4500's and 4700's running in production with the ATM card. Their throughput is limited by the CPU performance, but you can expect to get upwards of 40Mbps through it. If you want more than an OC3 I would suggest you look at something like a 7600 OSR, not speaking on behalf of any company in particular of course. Now we just need a Telco or three in NZ to support ATM at STM-4 rates. Arron Scott -----Original Message----- From: owner-nznog(a)list.waikato.ac.nz [mailto:owner-nznog(a)list.waikato.ac.nz]On Behalf Of Dennis Su Sent: Tuesday, 20 February 2001 7:04 p.m. To: nznog(a)list.waikato.ac.nz Subject: ATM card in Cisco 4500 Hi, We would like to purchase a ATM card for a Cisco 4500. Someone has mentioned to us that its ATM card is not very stable, although I doubt it. 4500 series router has been on the market for such a long time after all. I wonder if anyone can give us some previous experience. Good or bad and what type, all welcome. Thanks, Dennis ------------------------------------------------------------------------ ---- ----------------- Dennis Su, BSc MSc Network+ MCP CCNA CCDA CCNP CCDP Team Leader, Network Admin and Development IT Infrastructure, ITS, University of Waikato Hamilton, New Zealand phone:64 7 838 4183 email:d.su(a)waikato.ac.nz http://network-services.its.waikato.ac.nz/people/dennis.html --------- To unsubscribe from nznog, send email to majordomo(a)list.waikato.ac.nz where the body of your message reads: unsubscribe nznog --------- To unsubscribe from nznog, send email to majordomo(a)list.waikato.ac.nz where the body of your message reads: unsubscribe nznog

6 11

software required -- could be urgent
by Chris Wedgwood 24 Feb '01

24 Feb '01

... but probably it's not. Serious network software required. Only the network part isn't completely true :) I _need_ RollCage or RollCage II -- if I don't get this I'm sure something serious will happen; the entire Internet will stop routing or something. I am sure it will. I can feel it. I know the former was for sale at the warehouse for 20 bucks or so, but I can't find it now... the later, no idea. They are both old games by todays standards. Someone somewhere must have either both or one of these games. ... please ... :) --cw P.S. SPAM SPAM SPAM SPAM SPAM SPAM SPAM! --------- To unsubscribe from nznog, send email to majordomo(a)list.waikato.ac.nz where the body of your message reads: unsubscribe nznog

1 0

RE: ATM card in Cisco 4500
by Scott, Arron 23 Feb '01

23 Feb '01

ATM is FAR WORSE than that, but it helps sell stuff in New Zealand ;-) Arron Scott Not speaking for any company in particular -----Original Message----- From: Joe Abley [mailto:jabley(a)automagic.org] Sent: Friday, 23 February 2001 3:49 a.m. To: Scott, Arron Cc: Dennis Su; nznog(a)list.waikato.ac.nz Subject: Re: ATM card in Cisco 4500 On Thu, Feb 22, 2001 at 02:17:09PM +1100, Scott, Arron wrote: > Now we just need a Telco or three in NZ to support ATM at STM-4 > rates. Is anybody really waiting for that? If you're shifting an STM-4s worth of data around, it's probably a stream of packets, and it's probably IP, and you probably want to use POS. You probably don't want the additional complexity, cost, operational overhead, cell tax and SAR latency that using ATM would involve. Also, ATM is the work of Satan, which should be mentioned, for the record. Joe --------- To unsubscribe from nznog, send email to majordomo(a)list.waikato.ac.nz where the body of your message reads: unsubscribe nznog

6 5

RE: ATM card in Cisco 4500
by Scott, Arron 22 Feb '01

22 Feb '01

Yeah yeah ... we're all telling the Service Providers that Broadband is critical, but that still doesn't change the fact that ATM aggregation, ADSL/FR access, legacy support, and the ability to run a fair bit of point-to-point bandwidth over an STM-4 ATM access is still quite attractive for a market like NZ. And being one who had to fight VERY hard to get POS inside a certain Telco here at all, I would love to see more widespread use of it. STM/4 ATM gives my customers what they want and need, not what I want to sell !!! Arron Scott -----Original Message----- From: dean(a)flatnet.gen.nz [mailto:dean(a)flatnet.gen.nz] Sent: Friday, 23 February 2001 4:45 p.m. To: Scott, Arron Cc: Joe Abley; nznog(a)list.waikato.ac.nz Subject: Re: ATM card in Cisco 4500 I'd rather sell something that had a future, and not cripple networking in NZ any more than it already is. No matter how much easier it made the sale. Customers listen to what vendors have to say. Vendors should be telling them the truth, not just what they think will make the sale. Long live POS =) Dean Not speaking for, or about, any company in particular On Fri, Feb 23, 2001 at 02:01:55PM +1100, Scott, Arron wrote: > ATM is FAR WORSE than that, but it helps sell stuff in New Zealand ;-) > > Arron Scott > Not speaking for any company in particular > > -----Original Message----- > From: Joe Abley [mailto:jabley(a)automagic.org] > Sent: Friday, 23 February 2001 3:49 a.m. > To: Scott, Arron > Cc: Dennis Su; nznog(a)list.waikato.ac.nz > Subject: Re: ATM card in Cisco 4500 > > > On Thu, Feb 22, 2001 at 02:17:09PM +1100, Scott, Arron wrote: > > Now we just need a Telco or three in NZ to support ATM at STM-4 > > rates. > > Is anybody really waiting for that? If you're shifting an STM-4s worth > of data around, it's probably a stream of packets, and it's probably IP, > and you probably want to use POS. You probably don't want the additional > complexity, cost, operational overhead, cell tax and SAR latency that > using ATM would involve. > > Also, ATM is the work of Satan, which should be mentioned, for the > record. > > > Joe > --------- > To unsubscribe from nznog, send email to majordomo(a)list.waikato.ac.nz > where the body of your message reads: > unsubscribe nznog --------- To unsubscribe from nznog, send email to majordomo(a)list.waikato.ac.nz where the body of your message reads: unsubscribe nznog

1 0

Re: ATM card in Cisco 4500
by dean＠flatnet.gen.nz 21 Feb '01

21 Feb '01

Having a look on the Cisco Web site it seems that the fastest interface is an oc3. http://www.cisco.com/univercd/cc/td/doc/pcat/4700m.htm It might be an old website though. If it were me I would POC this to death before I bought it. The 4500 is pretty old and MAY not be able to feed an oc12 and do everything that you want it to do. Dean (Who does not speak on behalf of any employer) On Thu, Feb 22, 2001 at 11:40:17AM +1300, Lindsay Druett wrote: > OC12 > > -----Original Message----- > From: dean(a)flatnet.gen.nz [mailto:dean(a)flatnet.gen.nz] > Sent: Thursday, 22 February 2001 11:39 > To: nznog(a)list.waikato.ac.nz > Subject: Re: ATM card in Cisco 4500 > > > > On Wed, Feb 21, 2001 at 04:04:21PM +1300, Dennis Su wrote: > > > We would like to purchase a ATM card for a Cisco 4500. Someone has > > > mentioned to us that its ATM card is not very stable, although I doubt > it. > > > 4500 series router has been on the market for such a long time after > all. I > > > wonder if anyone can give us some previous experience. Good or bad and > what > > > type, all welcome. > > What speed ATM are you talking here? > > > Dean > (Who does not speak on behalf of any employer) > --------- > To unsubscribe from nznog, send email to majordomo(a)list.waikato.ac.nz > where the body of your message reads: > unsubscribe nznog --------- To unsubscribe from nznog, send email to majordomo(a)list.waikato.ac.nz where the body of your message reads: unsubscribe nznog

2 2

Re: ATM card in Cisco 4500
by dean＠flatnet.gen.nz 21 Feb '01

21 Feb '01

=) No Problems. I'd still POC it, But thats just me. Dean (Who does not speak on behalf of any employer) On Thu, Feb 22, 2001 at 12:06:03PM +1300, Lindsay Druett wrote: > I beg your pardon, it is an OC3 indeed (what was I thinking ?) > > -----Original Message----- > From: dean(a)flatnet.gen.nz [mailto:dean(a)flatnet.gen.nz] > Sent: Thursday, 22 February 2001 11:50 > To: Lindsay Druett; nznog(a)list.waikato.ac.nz > Subject: Re: ATM card in Cisco 4500 > > > > Having a look on the Cisco Web site it seems that the fastest interface is > an oc3. > http://www.cisco.com/univercd/cc/td/doc/pcat/4700m.htm > > It might be an old website though. > > If it were me I would POC this to death before I bought it. The 4500 is > pretty old and MAY not be able to feed an oc12 and do everything that you > want it to do. > > > Dean > (Who does not speak on behalf of any employer) > > On Thu, Feb 22, 2001 at 11:40:17AM +1300, Lindsay Druett wrote: > > OC12 > > > > -----Original Message----- > > From: dean(a)flatnet.gen.nz [mailto:dean(a)flatnet.gen.nz] > > Sent: Thursday, 22 February 2001 11:39 > > To: nznog(a)list.waikato.ac.nz > > Subject: Re: ATM card in Cisco 4500 > > > > > > > On Wed, Feb 21, 2001 at 04:04:21PM +1300, Dennis Su wrote: > > > > We would like to purchase a ATM card for a Cisco 4500. Someone has > > > > mentioned to us that its ATM card is not very stable, although I doubt > > it. > > > > 4500 series router has been on the market for such a long time after > > all. I > > > > wonder if anyone can give us some previous experience. Good or bad and > > what > > > > type, all welcome. > > > > What speed ATM are you talking here? > > > > > > Dean > > (Who does not speak on behalf of any employer) > > --------- > > To unsubscribe from nznog, send email to majordomo(a)list.waikato.ac.nz > > where the body of your message reads: > > unsubscribe nznog --------- To unsubscribe from nznog, send email to majordomo(a)list.waikato.ac.nz where the body of your message reads: unsubscribe nznog

1 0

ATM card in Cisco 4500
by Dennis Su 21 Feb '01

21 Feb '01

Hi, We would like to purchase a ATM card for a Cisco 4500. Someone has mentioned to us that its ATM card is not very stable, although I doubt it. 4500 series router has been on the market for such a long time after all. I wonder if anyone can give us some previous experience. Good or bad and what type, all welcome. Thanks, Dennis ---------------------------------------------------------------------------- ----------------- Dennis Su, BSc MSc Network+ MCP CCNA CCDA CCNP CCDP Team Leader, Network Admin and Development IT Infrastructure, ITS, University of Waikato Hamilton, New Zealand phone:64 7 838 4183 email:d.su(a)waikato.ac.nz http://network-services.its.waikato.ac.nz/people/dennis.html --------- To unsubscribe from nznog, send email to majordomo(a)list.waikato.ac.nz where the body of your message reads: unsubscribe nznog

3 2

FYI: ihug DNS server ips.
by Simon Lyall 20 Feb '01

20 Feb '01

Just a note that ihug is in the process of changing it's main DNS ips (as used by customers). Previously almost all customers were using 203.29.160.4 and 203.29.160.2 but we have now switched to 203.109.252.42 and 203.109.252.43. It is likely that there are 10,000s of ihug and ex-ihug customers with the old ip's manually setup in their configurations. Since we are returning these networks to Telstra they will cease being advertised outside our network sometime next week. You may wish to warn your helpdesk to keep an eye open for this. -- Simon Lyall. | Newsmaster | Work: simon.lyall(a)ihug.co.nz Senior Network/System Admin | | Home: simon(a)darkmere.gen.nz ihug, Auckland, NZ | Asst Doorman | Web: http://www.darkmere.gen.nz --------- To unsubscribe from nznog, send email to majordomo(a)list.waikato.ac.nz where the body of your message reads: unsubscribe nznog

1 0

New 2LD Voting - Feedback request
by Sue Leader 19 Feb '01

19 Feb '01

Greetings There will be a meeting of the Council of the Society this Friday the 23rd. The Council will consider the following options in regard to voting rights for new 2LD applications. Your comments are encouraged: ================= Motion 1 Abstract The Request for Votes for the .bank.nz application requires a voting electorate. After review and consideration 3 options have been presented for discussion and voting. Option 1 The electorate for the RFV shall be members of good standing of ISOCNZ as of the day before the vote is called. Reason: Known community that is easy to reach and identify which has a greater propensity to understand the issues surrounding the vote. Option 2 The electorate for the RFV shall be name holders or name holder representatives of a name in the .nz name space. A person would be only be able to vote once no matter how many names they had that qualified. Reason: The addition of a new 2LD directly affects current name holders. By having a name in the .nz spaces means they are an existing stakeholder in the .nz name space. Option 3 The electorate for the RFV shall be any person that has an email address in the .nz name space, i.e. steven.heath(a)isocnz.org.nz but not steven.heath(a)seranova.com. A person would be only be able to vote once no matter how many email addresses they had that qualified. Reason: By having an address in the .nz name space means they have an affinity with .nz and provides the widest possible community. Also does not exclude anyone based on having membership or an existing name. Preferred Motion 1 wording: That the electorate for the RFV for the .bank.nz be any person that has an email address in the .nz name space. A person would be only be able to vote once no matter how many email addresses they had that qualified. ======= Cheers Sue Sue Leader - Executive Director ISOCNZ (Internet Society of New Zealand Inc) Exe.Dir(a)isocnz.org.nz Voice: +64-4-801-6256 http://www.isocnz.org.nz PLEASE NOTE CHANGE: P.O.Box 11-881, Wellington --------- To unsubscribe from nznog, send email to majordomo(a)list.waikato.ac.nz where the body of your message reads: unsubscribe nznog

1 0

Deadline Extension - Green Paper
by Sue Leader 15 Feb '01

15 Feb '01

Greetings The Society has received requests for extension of the deadline for the SRS Implementation as the notification was not received by everyone on Feb 2 when I orginally sent it out. I resent the notice on the 8th, as even though the message went to the archives and some people had received it, clearly not everyone had. On that basis the Chair has agreed to an extension until Friday March 2 - 5:00pm. Please send all Submissions to me direct for collation. Cheers Sue Sue Leader - Executive Director ISOCNZ (Internet Society of New Zealand Inc) Exe.Dir(a)isocnz.org.nz Voice: +64-4-801-6256 http://www.isocnz.org.nz Postal: Level 1, (e)-Vision Centre, 282 Wakefield St, Wellington "Error: Press any key to continue or any other key to quit..." --------- To unsubscribe from nznog, send email to majordomo(a)list.waikato.ac.nz where the body of your message reads: unsubscribe nznog

3 2

ORBS blocking Domainz servers
by Don Stokes 15 Feb '01

15 Feb '01

Hello All, A heads-up for anyone using ORBS for spam filtering: ORBS has added the following manual entries to its database: 18.160.46.202.inputs.orbs.org IN TXT "Domainz.net.nz - Attacks on ORBS and ORBS hosters." 50.160.46.202.inputs.orbs.org IN TXT "Domainz.net.nz - Attacks on ORBS and ORBS hosters." 37.16.96.203.inputs.orbs.org IN TXT "Delivery point for Domainz.net.nz - Attacks on ORBS and ORBS hosters." These represent the hosts www.domainz.net.nz, office.domainz.net.nz and mail2.actrix.gen.nz respectively. The records were added on the 9th Feb 2001, according to the ORBS database web pages. The impact of this is that if a site is using ORBS for spam blocking, it will reject mail from the Domainz automated systems, including notifications of passwords, nameserver changes, reminders of accounts due and other automatically generated DRS notifications. It will also reject mail from the Actrix list server, which includes Domainz mailing lists, ISOCNZ mailing lists and presumably others. Normal customer service email should be unaffected, as these come from other Actrix hosts. Suffice to say, none of these addresses have been used to attack the ORBS service or systems, nor do the mail servers on these addresses relay spam or block ORBS queries. Email queries to ORBS by myself and Actrix staff have not elicited a reply. Unless ORBS decides to remove these records, anyone needing to to communicate (or having customers that may need to communicate) with Domainz should ensure that ORBS is not in use by their mail exchangers, or arrangements to bypass the blocks on the Domainz addresses are in place. -- don --------- To unsubscribe from nznog, send email to majordomo(a)list.waikato.ac.nz where the body of your message reads: unsubscribe nznog

15 23

zivo.co.nz (ex clearview.co.nz)
by PhoneNet 15 Feb '01

15 Feb '01

Following on from the ORBS discusion...... Anyone else having problems getting replies from zivo.co.nz (formerly clearview.co.nz) Our main email address was used to sign up to several porn sites from one of their IPs - The originating IP for the sign up process was recorded as: 202.78.157.14 which resolves to the address: >> router-cyber.cl.clearview.co.nz. Despite three emails regarding the matter I've had no response from them...... Ian Cousins --------- To unsubscribe from nznog, send email to majordomo(a)list.waikato.ac.nz where the body of your message reads: unsubscribe nznog

1 0

RE: Xtra / WIX
by Richard Naylor 14 Feb '01

14 Feb '01

At 03:35 PM 2/15/01 +1300, Ben Martel wrote: >Tony, > >It is the same for us (CLEAR) at the mo! Their router is there (ie. BGP is >active) but we are not exchanging any prefixes. > >I'm sure someone at Xtra is looking into it - right? Yep - I gave Peter a call about 2:40 and he had someone on the way to fix it. Sounded like internal switch failure/wedge. I understand dial-up users are down also - but then I don't use modems very often...... rich richard.naylor(a)citylink.co.nz --------- To unsubscribe from nznog, send email to majordomo(a)list.waikato.ac.nz where the body of your message reads: unsubscribe nznog

1 0

RE: Xtra / WIX
by Ben Martel 14 Feb '01

14 Feb '01

Tony, It is the same for us (CLEAR) at the mo! Their router is there (ie. BGP is active) but we are not exchanging any prefixes. I'm sure someone at Xtra is looking into it - right? ~benm --------- To unsubscribe from nznog, send email to majordomo(a)list.waikato.ac.nz where the body of your message reads: unsubscribe nznog

1 0

Xtra / WIX
by Tony Wicks 14 Feb '01

14 Feb '01

Hi all, my peering session with Xtra on WIX has disappeared, anyone know what has happened there ? --------- To unsubscribe from nznog, send email to majordomo(a)list.waikato.ac.nz where the body of your message reads: unsubscribe nznog

1 0

Who else is being spammed by Cisco Australia?
by Alan Brown 14 Feb '01

14 Feb '01

Subject says it all. Our copy arrived to our info@ address (which only appears on the website) with a botched attempt to address match it to one of the staff. So far the only response from Australia is that this is a legitimate marketing method, yadda yadda, usual spammer bullshit, and that the staffer should unsubscribe from the list if he doesn't want it. AB --------- To unsubscribe from nznog, send email to majordomo(a)list.waikato.ac.nz where the body of your message reads: unsubscribe nznog

2 1

prefix list update
by Tony Wicks 14 Feb '01

14 Feb '01

Hi all, I have an updated prefix list for those of you who we preer with ( as4770 ). There are no additions, I have been removing old unused networks only. ip prefix-list AONZ-networks description networks(a)nz.asiaonline.net ip prefix-list AONZ-networks seq 5 permit 202.14.100.0/24 ip prefix-list AONZ-networks seq 10 permit 210.48.0.0/17 ip prefix-list AONZ-networks seq 15 permit 192.173.16.0/21 ip prefix-list AONZ-networks seq 25 permit 202.6.84.0/24 ip prefix-list AONZ-networks seq 30 permit 202.12.70.0/24 ip prefix-list AONZ-networks seq 40 permit 202.36.36.0/22 ip prefix-list AONZ-networks seq 45 permit 202.36.76.0/23 ip prefix-list AONZ-networks seq 55 permit 202.37.76.0/24 ip prefix-list AONZ-networks seq 60 permit 202.37.85.0/24 ip prefix-list AONZ-networks seq 75 permit 202.37.140.0/22 ip prefix-list AONZ-networks seq 80 permit 202.37.148.0/24 ip prefix-list AONZ-networks seq 85 permit 202.37.144.0/21 ip prefix-list AONZ-networks seq 90 permit 202.37.163.0/24 ip prefix-list AONZ-networks seq 115 permit 202.37.197.0/24 ip prefix-list AONZ-networks seq 120 permit 202.37.200.0/22 ip prefix-list AONZ-networks seq 130 permit 202.37.224.0/21 ip prefix-list AONZ-networks seq 145 permit 202.37.252.0/24 ip prefix-list AONZ-networks seq 150 permit 202.49.144.0/24 ip prefix-list AONZ-networks seq 155 permit 202.50.16.0/20 ip prefix-list AONZ-networks seq 160 permit 203.99.65.0/24 ip prefix-list AONZ-networks seq 165 permit 203.99.66.0/24 ip prefix-list AONZ-networks seq 170 permit 203.99.71.0/24 ip prefix-list AONZ-networks seq 175 permit 210.54.0.0/22 ip prefix-list AONZ-networks seq 180 permit 138.235.0.0/16 ip prefix-list AONZ-networks seq 185 permit 203.9.180.0/24 cheers --------- To unsubscribe from nznog, send email to majordomo(a)list.waikato.ac.nz where the body of your message reads: unsubscribe nznog

1 0

Domainz
by David Buckingham 08 Feb '01

08 Feb '01

I find it interesting that a company which should be a leader in web development would leave something as simple as being able to miss out www undone http://domainz.net.nz doesn't work - WHY?!? How hard is it to make a 30 sec entry into bind? --------- To unsubscribe from nznog, send email to majordomo(a)list.waikato.ac.nz where the body of your message reads: unsubscribe nznog

2 1

Quik Internet havening spammer websites: Re: Baron-marketing.co.nz spamming yet again....
by J Random Luser 08 Feb '01

08 Feb '01

[This is an email copy of a Usenet post to "nz.net.admin"] Quik Internet claim to have taken action against this spammer. "We have removed Steve Baron's dialup account, so that he is unable to spam again from our network" well duh. He wasn't spamming from Quik in the first place. He was spamming for websites hosted _at_ Quik. It appears that Quik is another "Bulletproof web hosting provider", along with Palmerston North's Inspire.net http://www.mail-abuse.org/rbl/candidacy.html#ByAssociation --------- To unsubscribe from nznog, send email to majordomo(a)list.waikato.ac.nz where the body of your message reads: unsubscribe nznog

1 0

In case anyone missed it ... APRICOT2001
by Scott, Arron 07 Feb '01

07 Feb '01

CALL FOR PARTICIPATION in The one event where Asia Pacific Internet Infrastructure Engineers gather, talk tech and learn about the latest tools and techniques CwindowsTEMPnsmailL11.gif 26th Feb - 2 March 2001 Developing the Next Generation ASIA PACIFIC REGIONAL INTERNET CONFERENCE ON OPERATIONAL TECHNOLOGIES KUALA LUMPUR, MALAYSIA _____ Last year's APRICOT 2000, in Seoul, was the largest technical conference gathering of Asia Pacific Internet Engineers and Operators so far. The first APRICOT of the New Millennium, APRICOT 2001 will be held in Kuala Lumpur, Malaysia and is looking to be even more exciting & worthwhile! Apricot2001 will be hosted by the PIKOM, The Association of the Computer & Multimedia Industry of Malaysia and the Ministry of Energy, Communications & Multimedia of Malaysia. As in the past, the week-long summit will comprise of workshops, tutorials, conference sessions, Birds of a Feather (BOFs), and other forums, all geared towards spreading and sharing the knowledge required to operate the Internet within the Asia Pacific region. Not forgetting of course, exciting social events have also been planned for this year's Apricot. We have lined up some very distinguished speakers from the internet community including David Isenberg from Isen.com, Prof Jun Murai from KEIO University of Japan and Tan Sri Dr. Othman Yeop from the Multimedia Development Corporation of Malaysia. Hot topics covered include: IPv6 BGP MPLS: Protocols and Applications Gigabit Ethernet Streaming and Multicast Multilingual DNS Traffic Engineering & MPLS High Performance Routing DNSSEC, Bind V9, IPv6 Bind Network Security APNIC Address Policy pt2 Optical Networking Reverse DNS Virtual Private Networks Peering & Internet Exchanges QoS Panel ICANN UPDATE We are pleased to invite you to participate in this important event. The full conference program is available on the event site and registration can be submitted on-line at http://www.regweb.com/Apricot/2001 <http://www.apricot2001.net> . Meawhile, sponsorship opportunities are still available. Please log on to http://www.apricot2001.net/participation/sponsorship.html <http://www.apricot2001.net/participation/sponsorship.html> for details. We look forward to you joining us for the APRICOT2001 in Kuala Lumpur. Should you have any queries, please e-mail me. Kind regards, Molly Cheam Apricot2001 Secretariat c/o PIKOM, Association of the Computer & Multimedia Industry Malaysia

1 0