Don���t do that. Put customer routes in to BGP, use OSPF only to carry your loopbacks and router-router links for iBGP to use.
Keep your OSPF small, and your BGP big - it���s what they���re both good at.

(OSPF and ISIS are interchangeable here)

On 10/11/2017, at 2:45 PM, Nathan Brookfield <Nathan.Brookfield@simtronic.com.au> wrote:

Just running OSPF between them all wouldn���t solve that problem for you and worst case MPLS within a VRF?
 
Kindest Regards,
Nathan Brookfield (VK2NAB)
 
Chief Executive Officer
Simtronic Technologies Pty Ltd
 
Local: (02) 4749 4949 | Fax: (02) 4749 4950 | Direct: (02) 4749 4951


CONFIDENTIALITY & PRIVILEGE NOTICE

The information contained in this email and any attached files is strictly private and confidential. The intended recipient of this email may only use, reproduce, disclose or distribute the information contained in this email and any attached files with Simtronic Technologies Pty Ltd���s permission. If you are not the intended recipient, you are strictly prohibited from using, reproducing, adapting, disclosing or distributing the information contained in this email and any attached files or taking any action in reliance on it. If you have received this email in error, please email the sender by replying to this message, promptly delete and destroy any copies of this email and any attachments.

It is your responsibility to scan this communication and any files attached for computer viruses and other defects and recommend that you subject these to your virus checking procedures prior to use. Simtronic Technologies Pty Ltd does NOT accept liability for any loss or damage (whether direct, indirect, consequential, economic or other) however caused, whether by negligence or otherwise, which may result directly or indirectly from this communication or any files attached.

 
From: nznog-bounces@list.waikato.ac.nz [mailto:nznog-bounces@list.waikato.ac.nz] On Behalf Of Stan Rivett
Sent: Wednesday, November 8, 2017 10:52 AM
To: nznog <NZNOG@list.waikato.ac.nz>
Subject: Re: [nznog] BRAS Options
 
 
The multiple 7301 track was were I had been heading with one in Christchurch and one in Auckland. The problem is that most of our clients are RBI and we have no control over which router they appear on from our connections to Vodafone. That would be OK if we used dynamic IPs but we don't and its way too late to go back from that.

Stan Rivett
------------------
Netspeed
PO Box 5691
Dunedin
P: +64 3 481 7245
C: +64 21 323 841
------------------
 
On 8 November 2017 at 12:34, Sam Silvester <sam.silvester@gmail.com> wrote:
Hivemind :)
 
On Wed, Nov 8, 2017 at 9:56 AM, Gavin Tweedie <gavin.tweedie@megaport.com> wrote:
Can you tell Sam and I used to work at the same company? :)
 
On Wed, Nov 8, 2017 at 8:24 AM, Sam Silvester <sam.silvester@gmail.com> wrote:
To a point, the number of subscribers doesn't matter as much as the throughput. If you're looking at 16k+ subs on a single box, you probably need to start being a little careful but otherwise just make sure you've got a decent RP and you should be right. 

If you simply need to shift (say) 10Gbps of traffic with "more than a few thousand" but say less than 16k, then anything in the ASR range with an RP2 and ESP40 will almost certainly be ample.

Another thought, considering you mention the 7301, is to scale out horizontally - it's not clear if you're already doing this. The nice bit about that also is you could have a few 7201s sharing the load 4 ways, which means your IP pool overhead to cater for a box failure is also much less than running only two boxes.
 
On Wed, Nov 8, 2017 at 9:41 AM, Dave Mill <dave@mill.net.nz> wrote:
A Juniper MX40 or MX80 seems to meet your needs there - depending on exact subscriber figures. From memory if every customer is in QinQ you won't be able to have more than 8000 on a MX80 series chassis due to interface limits.
 
Dave
 
On Wed, Nov 8, 2017 at 12:07 PM, Stan Rivett <stan@netspeed.net.nz> wrote:
Crikey, thanks for all the replies
 
Yes we need 10 Gbit, at least 3 ports and I'd rather not be too specific about numbers but more than a few thousand.
 
Apologies for being a bit of a cheap bugger but you know what its like as an SME, it all comes out of my pocket ;-)
 
Cheers

Stan Rivett
------------------
Netspeed
PO Box 5691
Dunedin
------------------
 
On 8 November 2017 at 11:14, Tim Price <tim@initech.co.nz> wrote:
Juniper MX5 + licensing shouldn���t cost you more than $30k depending on your Juniper partner status and where you buy it from.
 
From: <nznog-bounces@list.waikato.ac.nz> on behalf of Stan Rivett <stan@netspeed.net.nz>
Date: Wednesday, 8 November 2017 at 11:02 AM
To: nznog <NZNOG@list.waikato.ac.nz>
Subject: [nznog] BRAS Options
 
Hi all
 
The time has come to replace my poor old Cisco 7301 and the quote I got for an ASR1002-HX made my eyes water. Still waiting for a Juniper quote but the general discussion seemed like similar numbers.
 
Are there any other reliable options out there that don't cost more than my first house?
 
Cheers
 
Stan Rivett
------------------
Netspeed
PO Box 5691
Dunedin
------------------
_______________________________________________ NZNOG mailing listNZNOG@list.waikato.ac.nz https://list.waikato.ac.nz/mailman/listinfo/nznog
 


_______________________________________________
NZNOG mailing list
NZNOG@list.waikato.ac.nz
https://list.waikato.ac.nz/mailman/listinfo/nznog

 


_______________________________________________
NZNOG mailing list
NZNOG@list.waikato.ac.nz
https://list.waikato.ac.nz/mailman/listinfo/nznog

 


_______________________________________________
NZNOG mailing list
NZNOG@list.waikato.ac.nz
https://list.waikato.ac.nz/mailman/listinfo/nznog



 
-- 
Global Interconnection Director
 


_______________________________________________
NZNOG mailing list
NZNOG@list.waikato.ac.nz
https://list.waikato.ac.nz/mailman/listinfo/nznog

 
_______________________________________________
NZNOG mailing list
NZNOG@list.waikato.ac.nz
https://list.waikato.ac.nz/mailman/listinfo/nznog