- NZNOG - lists.nznog.org

Re: Orcon APE connection woes
by Seeby Woodhouse - Orcon 13 Jun '01

13 Jun '01

Hmm we have forced full-duplex and turned off auto-negotiation on our Catalyst 5000 switch - but we have also tried all the other settings possible. Clear have told us to set it to 10Mbps Full-Duplex - so that's what it is at present. Cheers Seeby Orcon Internet - www.orcon.net.nz ----- Original Message ----- From: "Ian Quinn" <iquinn(a)juniper.net> To: "Seeby Woodhouse - Orcon" <seeby(a)orcon.net.nz> Sent: Wednesday, June 13, 2001 6:42 PM Subject: RE: Orcon APE connection woes > > I had some problems recently that were marginally similar. Although I had > the speed and duplex settings configured, it didn't come right until I > turned off auto negotiation as well (eg no negotiation or something along > those lines). > > No idea if it's your problem - just seems familiar. > > Good luck :-) > > Regards / Ian > > -----Original Message----- > > From: Seeby Woodhouse - Orcon [mailto:seeby(a)orcon.net.nz] > > Sent: Wednesday, 13 June 2001 6:27 p.m. > > To: NZNOG Mailing List > > Subject: Orcon APE connection woes > > > > > > Hi there everyone > > > > Orcon has just had a 10Mbit IPExpress connection to APE > > completed, and I > > have been fighting with it all day. > > > > If we ping anyone on APE, then we get around 2/3's of the > > pings through, and > > 1/3 are dropped. > > This happens in a pattern of 1/3 drop, 2/3 get through. > > > > I talked with Clear and they said that it could be the > > IPExpress connection > > re-negotiating because of what is on our end, so we have been > > playing with > > the settings on our Catalyst 5000 switch - we have forced the > > port to our > > IPExpress connection full duplex / half duplex / 100mb / 10mb > > but they all > > seem to give the same results. > > > > Clear has advised us to set our equipment to 10Mbit full > > duplex - so that's > > what it is at present. > > > > The connection from IPExpress is then VLan'd from our > > Catalyst switch into > > our core Cisco 7505 router. > > > > A ping report of 300 pings to ihug.ape.net.nz looks like this > > > > --------------------------------------------------- > > ORCON7505#ping > > Protocol [ip]: > > Target IP address: ihug.ape.net.nz > > Repeat count [5]: 300 > > Datagram size [100]: > > Timeout in seconds [2]: > > Extended commands [n]: > > Sweep range of sizes [n]: > > Type escape sequence to abort. > > Sending 300, 100-byte ICMP Echos to 192.203.154.36, timeout > > is 2 seconds: > > ........!!!!!!!!!!!!!!!!!!!!!..........!!!!!!!!!!!!!!!!..........!!!!! > > !!!!!!!!!!!!!!!...........!!!!!!!!!!!!!!!!!!!!!!...........!!!!!!!!!!! > > !!!!!!!!!!!!...........!!!!!!!!!!!!!!!!!!!!!!!!!...........!!!!!!!!!!! > > !!!!!!!!!...........!!!!!!!!!!!!!!!!!!!!!..........!!!!!!!!!!!!!!!!!!! > > !!..........!!!!!!!! > > Success rate is 65 percent (197/300), round-trip min/avg/max > > = 1/3/24 ms > > -------------------------------------------------- > > > > Can anyone shed any light on this? > > > > Is this related the the spanning tree problems that have been > > happening up > > at APE recently? > > Or should we be hassling Clear about the service..... > > > > Cheers > > Seeby > > > > Orcon Internet - www.orcon.net.nz > > > > > > --------- > > To unsubscribe from nznog, send email to majordomo(a)list.waikato.ac.nz > > where the body of your message reads: > > unsubscribe nznog > > > --------- To unsubscribe from nznog, send email to majordomo(a)list.waikato.ac.nz where the body of your message reads: unsubscribe nznog

4 6

Zfree Delibratley slowing down access to Orcon's network
by Seeby Woodhouse - Orcon 13 Jun '01

13 Jun '01

It seems that Zfree is delibratley slowing down Internet access to some of Orcon's internal network. If we test by dialing up using a Zfree account, most of our network is blazingly fast, however access to our Mail server and FreeHost server is painfully slow. (mail.orcon.net.nz and freehost.orcon.net.nz) Last time we informed them of this problem, the issue mysteriously went away - but now it is back again a week later. I suspect that Zfree is delibratley rate-shaping the amount of traffic that can go to our mail server and our freehost server from their network to prevent people from accessing them. It is quite frustrating when it is our helpdesk that is recieving all the calls (because theirs is 0900), when it is actually their problem - especially when the customers that are calling us are not actually using us for dialup. Any system administrators for Clear got something to say about this? ;-) -- Cheers Seeby Orcon Internet - www.orcon.net.nz --------- To unsubscribe from nznog, send email to majordomo(a)list.waikato.ac.nz where the body of your message reads: unsubscribe nznog

2 1

Re: Orcon APE connection woes
by Seeby Woodhouse - Orcon 12 Jun '01

12 Jun '01

Hi there Tim I don't want to put any traffic over to APE until this link is working properly. As you know, BGP won't detect packet loss, so it is still better to keep sticking all our Traffic via Telecom until this issue is resolved. As soon as the link works reliably - then we will want to peer with everyone that we can. Hopefully we'll be able to get sub 10ms pings to most ISP's in the country at the end of this ;-) Cheers Seeby Orcon Internet - www.orcon.net.nz ----- Original Message ----- From: "Tim Philips" <tim.philips(a)attica.co.nz> To: "Seeby Woodhouse - Orcon" <seeby(a)orcon.net.nz> Sent: Wednesday, June 13, 2001 6:52 PM Subject: Re: Orcon APE connection woes > On Wed, 13 Jun 2001, Seeby Woodhouse - Orcon wrote: > > Seeby, > > We have had this problem before. Well are still having it with our > Tangent 100Mb. I will see what I can find. Would you like to peer with > us also once your link is up and running. > > If you do provide us with a prefix list and I or one of the other guys > will sort it all out. > > > Hi there everyone > > > > Orcon has just had a 10Mbit IPExpress connection to APE completed, and I > > have been fighting with it all day. > > > > If we ping anyone on APE, then we get around 2/3's of the pings through, and > > 1/3 are dropped. > > This happens in a pattern of 1/3 drop, 2/3 get through. > > > > I talked with Clear and they said that it could be the IPExpress connection > > re-negotiating because of what is on our end, so we have been playing with > > the settings on our Catalyst 5000 switch - we have forced the port to our > > IPExpress connection full duplex / half duplex / 100mb / 10mb but they all > > seem to give the same results. > > > > Clear has advised us to set our equipment to 10Mbit full duplex - so that's > > what it is at present. > > > > The connection from IPExpress is then VLan'd from our Catalyst switch into > > our core Cisco 7505 router. > > > > A ping report of 300 pings to ihug.ape.net.nz looks like this > > > > --------------------------------------------------- > > ORCON7505#ping > > Protocol [ip]: > > Target IP address: ihug.ape.net.nz > > Repeat count [5]: 300 > > Datagram size [100]: > > Timeout in seconds [2]: > > Extended commands [n]: > > Sweep range of sizes [n]: > > Type escape sequence to abort. > > Sending 300, 100-byte ICMP Echos to 192.203.154.36, timeout is 2 seconds: > > ........!!!!!!!!!!!!!!!!!!!!!..........!!!!!!!!!!!!!!!!..........!!!!! > > !!!!!!!!!!!!!!!...........!!!!!!!!!!!!!!!!!!!!!!...........!!!!!!!!!!! > > !!!!!!!!!!!!...........!!!!!!!!!!!!!!!!!!!!!!!!!...........!!!!!!!!!!! > > !!!!!!!!!...........!!!!!!!!!!!!!!!!!!!!!..........!!!!!!!!!!!!!!!!!!! > > !!..........!!!!!!!! > > Success rate is 65 percent (197/300), round-trip min/avg/max = 1/3/24 ms > > -------------------------------------------------- > > > > Can anyone shed any light on this? > > > > Is this related the the spanning tree problems that have been happening up > > at APE recently? > > Or should we be hassling Clear about the service..... > > > > Cheers > > Seeby > > > > Orcon Internet - www.orcon.net.nz > > > > > > --------- > > To unsubscribe from nznog, send email to majordomo(a)list.waikato.ac.nz > > where the body of your message reads: > > unsubscribe nznog > > > > -- > Thanks, > Tim Philips > --------- To unsubscribe from nznog, send email to majordomo(a)list.waikato.ac.nz where the body of your message reads: unsubscribe nznog

1 0

Orcon APE connection woes
by Seeby Woodhouse - Orcon 12 Jun '01

12 Jun '01

Hi there everyone Orcon has just had a 10Mbit IPExpress connection to APE completed, and I have been fighting with it all day. If we ping anyone on APE, then we get around 2/3's of the pings through, and 1/3 are dropped. This happens in a pattern of 1/3 drop, 2/3 get through. I talked with Clear and they said that it could be the IPExpress connection re-negotiating because of what is on our end, so we have been playing with the settings on our Catalyst 5000 switch - we have forced the port to our IPExpress connection full duplex / half duplex / 100mb / 10mb but they all seem to give the same results. Clear has advised us to set our equipment to 10Mbit full duplex - so that's what it is at present. The connection from IPExpress is then VLan'd from our Catalyst switch into our core Cisco 7505 router. A ping report of 300 pings to ihug.ape.net.nz looks like this --------------------------------------------------- ORCON7505#ping Protocol [ip]: Target IP address: ihug.ape.net.nz Repeat count [5]: 300 Datagram size [100]: Timeout in seconds [2]: Extended commands [n]: Sweep range of sizes [n]: Type escape sequence to abort. Sending 300, 100-byte ICMP Echos to 192.203.154.36, timeout is 2 seconds: ........!!!!!!!!!!!!!!!!!!!!!..........!!!!!!!!!!!!!!!!..........!!!!! !!!!!!!!!!!!!!!...........!!!!!!!!!!!!!!!!!!!!!!...........!!!!!!!!!!! !!!!!!!!!!!!...........!!!!!!!!!!!!!!!!!!!!!!!!!...........!!!!!!!!!!! !!!!!!!!!...........!!!!!!!!!!!!!!!!!!!!!..........!!!!!!!!!!!!!!!!!!! !!..........!!!!!!!! Success rate is 65 percent (197/300), round-trip min/avg/max = 1/3/24 ms -------------------------------------------------- Can anyone shed any light on this? Is this related the the spanning tree problems that have been happening up at APE recently? Or should we be hassling Clear about the service..... Cheers Seeby Orcon Internet - www.orcon.net.nz --------- To unsubscribe from nznog, send email to majordomo(a)list.waikato.ac.nz where the body of your message reads: unsubscribe nznog

1 0

WHOIS Survey - DNSO
by Andy Linton 12 Jun '01

12 Jun '01

The DNSO is conducting a survey on ICANN's WHOIS policy. http://www.icann.org/dnso/whois-survey-en-10jun01.htm --------- To unsubscribe from nznog, send email to majordomo(a)list.waikato.ac.nz where the body of your message reads: unsubscribe nznog

1 0

RE: subscribe NZOG
by Lindsay Druett 12 Jun '01

12 Jun '01

How does the subscribe kit work ? > -----Original Message----- > From: Michael White [mailto:MWHITE(a)clear.co.nz] > Sent: Wednesday, 13 June 2001 14:40 > To: Michael White; nznog(a)list.waikato.ac.nz; 'Juha Saarinen' > Subject: RE: subscribe NZOG > > Damn, wrong kit. > > Mike > > ---------- > From: Juha Saarinen > Sent: Wednesday, 13 June 2001 2:33 PM > To: 'Michael White'; nznog(a)list.waikato.ac.nz > Subject: RE: subscribe NZOG > > Heres how to unsubscribe: > > > Errr... I think the person wants to subscribe. > > -- Juha > > --------- To unsubscribe from nznog, send email to majordomo(a)list.waikato.ac.nz where the body of your message reads: unsubscribe nznog

1 0

RE: subscribe NZOG
by Michael White 12 Jun '01

12 Jun '01

Damn, wrong kit. Mike > ---------- > From: Juha Saarinen > Sent: Wednesday, 13 June 2001 2:33 PM > To: 'Michael White'; nznog(a)list.waikato.ac.nz > Subject: RE: subscribe NZOG > > Heres how to unsubscribe: > > > Errr... I think the person wants to subscribe. > > -- Juha > >

2 1

RE: subscribe NZOG
by Michael White 12 Jun '01

12 Jun '01

> ---------- > From: Te Aroha > Sent: Wednesday, 13 June 2001 2:13 PM > To: nznog(a)list.waikato.ac.nz > Subject: subscribe NZOG > > Hi there > > Can you please subscribe me to this mailing list. > > Cheers > > > Te Aroha > Maxnet Support Team > Customer Services Supervisor > support(a)maxnet.co.nz > Ph: 0508 MAXNET > Ph: (09) 300-7555 Tech Support > Ph: (09) 300-7222 Office > > > > Heres how to unsubscribe: > > First, ask your Internet Provider to mail you an Unsubscribing Kit. > Then follow these directions. > > The kit will most likely be the standard no-fault type. Depending on > requirements, System A and/or System B can be used. When operating > System A, depress lever and a plastic dalkron unsubscriber will be > dispensed through the slot immediately underneath. When you have > fastened the adhesive lip, attach connection marked by the large "X" > outlet hose. Twist the silver- coloured ring one inch below the > connection point until you feel it lock. > > The kit is now ready for use. The Cin-Eliminator is activated by the > small switch on the lip. When securing, twist the ring back to its > initial condition, so that the two orange lines meet. Disconnect. > Place the dalkron unsubscriber in the vacuum receptacle to the rear. > Activate by pressing the blue button. > > The controls for System B are located on the opposite side. The red > release switch places the Cin-Eliminator into position; it can be > adjusted manually up or down by pressing the blue manual release > button. The opening is self- adjusting. To secure after use, press > the green button, which simultaneously activates the evaporator and > returns the Cin-Eliminator to its storage position. > > You may log off if the green exit light is on over the evaporator . > If the red light is illuminated, one of the Cin-Eliminator > requirements has not been properly implemented. Press the "List Guy" > call button on the right of the evaporator . He will secure all > facilities from his control panel. > > To use the Auto-Unsub, first undress and place all your clothes in > the clothes rack. Put on the velcro slippers located in the cabinet > immediately below. Enter the shower, taking the entire kit with you. > On the control panel to your upper right upon entering you will see a > "Shower seal" button. Press to activate. A green light will then be > illuminated immediately below. On the intensity knob, select the > desired setting. Now depress the Auto-Unsub activation lever. Bathe > normally. > > The Auto-Unsub will automatically go off after three minutes unless > you activate the "Manual off" override switch by flipping it up. When > you are ready to leave, press the blue "Shower seal" release button. > The door will open and you may leave. Please remove the velcro > slippers and place them in their container. > > If you prefer the ultrasonic log-off mode, press the indicated blue > button. When the twin panels open, pull forward by rings A & B. The > knob to the left, just below the blue light, has three settings, low, > medium or high. For normal use, the medium setting is suggested. > > After these settings have been made, you can activate the device by > switching to the "ON" position the clearly marked red switch. If > during the unsubscribing operation, you wish to change the settings, > place the "manual off" override switch in the "OFF" position. You may > now make the change and repeat the cycle. When the green exit light > goes on, you may log off and have lunch. Please close the door behind > you. > > > >

2 1

My Bad
by Te Aroha 12 Jun '01

12 Jun '01

OK ppl's My Bad I submitted to this list instead of majordomo...Cheers to Brendan Willis, Mark Little, Gavin Quayle and crew for sorting me out...I guess supervising you guys taught me nothing. :) Te Aroha Maxnet Support Team tearoha(a)maxnet.co.nz t(a)maxnet.co.nz

1 0

subscribe NZOG
by Te Aroha 12 Jun '01

12 Jun '01

Hi there Can you please subscribe me to this mailing list. Cheers Te Aroha Maxnet Support Team Customer Services Supervisor support(a)maxnet.co.nz Ph: 0508 MAXNET Ph: (09) 300-7555 Tech Support Ph: (09) 300-7222 Office

1 0